This article shows the necessary steps for mounting the Verkada CB51/61 camera on a wall.

Quick Video Overview

In the CB51 box

  • 1 CB41 Camera
  • 1 Mount Plate
  • 1 Setup guide, with 2 mounting templates
  • 1 T8, T25 Hand Tool
  • 1 22mm cable gland wrench
  • 4 Wall mounting screws & anchors
  • 4 Adapter mounting screws
  • 1 Conduit adapter
  • 1 Junction box adapter and cover plate

You will need

  • A working internet connection
  • 802.3af Power over Ethernet (PoE) switch or a PoE injector. For operation below -20C, use 802.3at PoE
  • A smartphone or laptop
  • A #2 Phillips screwdriver or power drill with a #2 Phillips driver bit
  • 1/4 inch (6.5mm) drill bit for wall anchors
  • 1/8 inch (3mm) drill bit for pilot holes
  • A Cat5 or Cat6 ethernet cable

Overview

Connect

  • Use the T8 drive to loosen the set screws. Do not completely remove the screws
  • Twist the ring at the base of the housing to remove the outer cover
  • Insert the ethernet cable into the ethernet port. Scan the QR code for easy camera registration and setup, or proceed to www.verkada.com/start

Anchoring

  • To unlock the Wall Mount from the Base Plate, loosen the Base Locking SCew using the provided T8 hand tool. The screw should be backed out approximately .2" (5mm) from the Base Plate. Do not fully remove the screw
  • To remove the Wall Mount from the Base Plate, twist the Wall Mount counterclockwise then pull the wall Mount off of the underside of the Base Plate
  • use the provided mounting template to mark wall mount holes. For a solid material like wood or metal, drill 1/8 inch pilot holes. Drive mounting screws directly into the pilot holes. For drywall, drill 1/4 inch holes, insert plastic anchors into holes and drive mounting screws into anchors

Mounting

  • Feed the ethernet cable through the center of the wall mount before fully securing it to the mounting surface. Leave enough slack to safely hand the camera during the cable gland installation
  • Remove the cable gland from CB51. Route the ethernet cable through the base and ball joint. Leave the cable disconnected for now
  • Align mounting features on the wall Mount with the mounting pegs on the backslide of the CB51 base, then engage the mounting pegs clockwise until you feel the camera lock securely in place, tighten the T8 security screw
  • Feed the ethernet cable through the center of the wall mount before fully securing it to the mounting surface. Leave enough slack to safely hand the camera during the cable gland installation
  • Remove the cable gland from the CB51
  • Route the ethernet

Cabling

  • Firmly push the rubber seal and plastic collar together
  • Slide the metal nut over the RJ45 connector and engage the threads on the pass-through
  • Slide the cable gland assembly into the pass through, seating it in position
  • Gently tighten down the metal nut by hand You should still be able to move the cable back and forth through the gland

Gasket and rubber seal

  • Push the excess ethernet cable back through the cable gland assembly. Plug in the ethernet cable to the camera's RJ45 jack. The cable should be routed straight from the cable gland into the RJ45 jack.
  • Firmly tighten the metal nut using the included wrench until no threads are visible

Final assembly

  • To finish securing the device, align the outer cover with the camera and push into place. The external threads on the outer cover will meet the internal threads on the ring at the back of the housing
  • Rotate the ring to thread the outer housing into place. The outer housing will be pulled into place and should seat against the ring when fully tightened.
  • Use the T8 security key to tighten one of the set screws on the side of the ring to increase tamper resistance

Adjusting

  • Adjust your camera to the desired viewing angle. Use the online stream to confirm image orientation. Image can be flipped 180 degrees in Command.
  • To lock the camera in place, use the T25 security torx key to turn the screw on the side of the stand. This will tighten the ball joint. To fully secure the device, rotate the torx handle 90 degrees and tighten the screw further
  • Remove film protector off the lens

Did this answer your question?